You will get a notification that says HP Printer ErrorCode out of paper or “Load Paper,” and the printer will not move to load paper.
These are the steps you must follow. To determine if you’ve solved the problem, print out each assignment after completing it.
Verify the documents, and then run them through the presses again
When delivering a product, make sure to look for any paper that has become wrinkled, torn, or bent, since these things can lead to problems with receiving your goods.
- Step 1 :-> Clear the paper tray.
- Step 2 :->Peeling apart the stack of paper will take out all of the damaged sheets.
- Step 3 :->Inspect the paper tray for anything that could block the path of the print job. Ensure the paper is able to make contact with the rollers.
- Step 4 :->To avoid uneven paper stacks, ensure that all edges are of equal height.
- Step 5 :->Load the paper tray with the stack of paper.
- Step 6 :->Ensure that the paper tray is secured.
- Step 7 :->On the printer control panel or in the printer software, pick the suitable paper size.
Necessary to clean the paper pick rollers (top paper tray)
Remove contaminants, such as paper particles and dirt, from the paper feed rollers to improve the feeding of documents.
- Step 1 :->The rollers on the top paper tray need to be cleaned.
- Step 2 :->Please grab a flashlight.
- Step 3 :->End the print job.
- Step 4 :->Disconnect the power cord from the printer only when the printer is not in use and is silent.
- Step 5 :->To begin, remove the stack of paper from the input tray.
- Step 6 :->Search within the input tray for the paper pick rollers, using the flashlight.
- Step 7 :->An illustration of top-loading printer paper pick rollers
- Step 8 :->A moistened cotton swab should be wrung out to expel extra water.
- Step 9 :->Turn the rollers and swab them thoroughly to remove any excess ink.
- Step 10 :->Allow the rollers to sit for two minutes before putting them away.
- Step 11 :->Then, make sure to plug the printer back in before turning it on.
Necessary to clean the paper pick rollers (under printer)
To properly clean the paper pick rollers on a printer with a bottom-loading paper tray, you must clear out the paper debris.
- Step 1 :->End the print job.
- Step 2 :->Wait until the printer is completely quiet before disconnecting the cords and power cord.
- Step 3 :->To begin, remove the stack of paper from the input tray.
- Step 4 :->Pick it up and set it on its side or upside down.
- Step 5 :->To discover the grey paper pick rollers, locate the paper tray and then pull it out.
- Step 6 :->Paper support rollers that are installed under the printer.
- Step 7 :->A moistened cotton swab should be wrung out to expel extra water.
- Step 8 :->Turn the rollers and swab them thoroughly to remove any excess ink.
- Step 9 :->Allow the rollers to sit for two minutes before putting them away.
- Step 10 :->Make sure the printer is standing straight.
- Step 11 :->Then, make sure to plug the printer back in before turning it on.
Necessary to clean the paper pick rollers (inside printer)
You should clean the paper pick rollers inside the paper tray or under the cartridge (if necessary).
- Step 1 :->Please grab a flashlight.
- Step 2 :->End the print job.
- Step 3 :->Wait until the printer is completely quiet before disconnecting the cords and power cord.
- Step 4 :->To begin, remove the stack of paper from the input tray.
- Step 5 :->To locate the paper pick roller, first use a flashlight to check your printer model.
- Step 6 :->A moistened cotton swab should be wrung out to expel extra water.
- Step 7 :->Turn the rollers and swab them thoroughly to remove any excess ink.
- Step 8 :->Allow the rollers to sit for two minutes before putting them away.
- Step 9:->To activate the printer, reconnect the wires and power cord and turn it on.
Reset the printer’s settings
- Step 1 :->Go to the printer’s settings to recover from printer issues and to get it working again.
- Step 2 :->Unplug the printer from the power cord after it is switched on.
- Step 3 :->Unplug the power cord.
- Step 4 :->You should wait 60 seconds.
- Step 5 :->Power up the printer by plugging it back in to a wall socket and the printer.
- Step 6 :->According to HP, printing should occur via a direct connection to the wall.
- Step 7 :->Complete the reset by activating the printer.
Discloser :-
If the HP Printer ErrorCode out of paper , you can have your printer repaired. We hope the above solution can help you fix your Printer Errorcode out of paper .
We help you to Fix your all Printer Error Visit now Printererrorfix.com to solve your error.